Message-ID: <019201c275e6$0bad2660$0500000a@webadmin2> From: "Billy Huddleston" <billy@nxs.net> Subject: Re: [Emerald] USR Total Control - Framed Route - Radius Date: Thu, 17 Oct 2002 10:04:01 -0400
Opps.. Ment Framed-Netmask, not Framed-Subnet.. Sorry
Should be right below Framed-Address We don't assign a WAN IP and then a
route.. I.E. We use un-numbered interface.. (Sometimes people will assign a
/30 to the BRI interface and then route a /27 or whatever to that interface,
wase of a /30 for ISDN.) Anyway, In 2.5 it is right below Framed-Address
Thanks, Billy
----- Original Message -----
From: "Network Operations" <admin@isoc.net>
To: <emerald@iea-software.com>
Sent: Thursday, October 17, 2002 9:51 AM
Subject: RE: [Emerald] USR Total Control - Framed Route - Radius
> Framed Subnet sounds like what I want.
>
> ie: pipeline 50 get a framed-address for its wan interface
> then I have been adding routes for a /30 or /28 subnet in the cli
> to their framed address.
>
> then they use one of the ip's for the Ethernet interface on the pipeline
> and the remaining ip's on their network.
>
> It sounds to me like you are saying I can do this with the
> framed-subnet?
>
> only problem is I cannot find that attribute :(
>
> I am using emerald 2.5 and radius 2.something
>
> -----Original Message-----
> From: emerald-request@iea-software.com
> [mailto:emerald-request@iea-software.com] On Behalf Of Billy Huddleston
> Sent: Thursday, October 17, 2002 9:50 AM
> To: emerald@iea-software.com
> Subject: Re: [Emerald] USR Total Control - Framed Route - Radius
>
> I never use Framed-Route unless they have more than 1 subnet..
> Otherwise, I
> just assign them a
> static ip address with the Framed-Subnet.. They get the whole subnet
> routed
> to them that way..
>
> I think it's net/subnet gateway metrix .. So... 192.168.0.0/24
> 192.168.2.1 1
> I think.. Been a while since I've done one of those..
>
> Thanks, Billy
>
>
> ----- Original Message -----
> From: "Network Operations" <admin@isoc.net>
> To: <emerald@iea-software.com>
> Sent: Thursday, October 17, 2002 9:37 AM
> Subject: [Emerald] USR Total Control - Framed Route - Radius
>
>
> >
> > Hello all,
> >
> > I am trying to figure out how to get Radius to assign
> > a route to my hiper-arc for dial ISDN customers.
> >
> > The customers have static framed addresses assigned
> > and I usually add the route in the hiper-arc thru the
> > CLI but sometimes they get lost after a reboot.
> >
> > So I am trying to use the Framed-Route attribute but
> > not sure what to put in the value? what is the proper
> > format? Is it something like destination x.x.x.x
> > gateway x.x.x.x metric x. Or is it the command I would
> > use if I was doing it in the hiper-arc cli? ie:
> > add route x.x.x.x/x gateway x.x.x.x metric x
> >
> > Anyone have any ideas?
> >
> > TIA
> > John
> >
> > ------------
> >
> > This is a user supported list. If you require assistance from IEA
> Software's
> > Support Engineers, please check out our Support resources at
> > http://www.iea-software.com/support.
> >
> > For more information about this list (including removal) go to:
> > http://www.iea-software.com/support/maillists/liststart
> >
>
> ------------
>
> This is a user supported list. If you require assistance from IEA
> Software's
> Support Engineers, please check out our Support resources at
> http://www.iea-software.com/support.
>
> For more information about this list (including removal) go to:
> http://www.iea-software.com/support/maillists/liststart
>
> ------------
>
> This is a user supported list. If you require assistance from IEA
Software's
> Support Engineers, please check out our Support resources at
> http://www.iea-software.com/support.
>
> For more information about this list (including removal) go to:
> http://www.iea-software.com/support/maillists/liststart
>