------_=_NextPart_000_01BDFDCF.A3042F40
Content-Type: multipart/alternative;
boundary="----_=_NextPart_001_01BDFDCF.A3042F40"
------_=_NextPart_001_01BDFDCF.A3042F40
Content-Type: text/plain
Your message
To: radiusnt@iea-software.com
Subject: Radius Acct problems
Sent: Thu, 22 Oct 1998 10:06:07 -0500
did not reach the following recipient(s):
madams@orca.net on Thu, 22 Oct 1998 10:21:24 -0500
The recipient name is not recognized
MSEXCH:IMS:Orca Technologies Inc.:OTEXS1:OTBDC1 0 (000C05A6) Unknown
Recipient
------_=_NextPart_001_01BDFDCF.A3042F40
Content-Type: text/html
<!DOCTYPE HTML PUBLIC "-//W3C//DTD HTML 3.2//EN">
Your message
To: radiusnt@iea-software.com
Subject: Radius Acct problems
Sent: Thu, 22 Oct 1998 10:06:07 -0500
did not reach the following recipient(s):
madams@orca.net on Thu, 22 Oct 1998 10:21:24 -0500
The recipient name is not recognized
MSEXCH:IMS:Orca Technologies Inc.:OTEXS1:OTBDC1 0 (000C05A6) Unknown Recipient
------_=_NextPart_001_01BDFDCF.A3042F40--
------_=_NextPart_000_01BDFDCF.A3042F40
Content-Type: message/rfc822
Content-Location: ATT-0-0293312BB969D211A43500805F8AF4A3
Message-ID: <C1F8D4F318BDD0119F7300AA00B198011A5177@master.cape-fear.net>
From: rbryn@cape-fear.net
To: radiusnt@iea-software.com
Subject: Radius Acct problems
Date: Thu, 22 Oct 1998 10:06:07 -0500
MIME-Version: 1.0
X-Mailer: Internet Mail Service (5.5.2232.9)
X-MS-Embedded-Report:
Content-Type: multipart/alternative;
boundary="----_=_NextPart_003_01BDFDCF.A3042F40"
------_=_NextPart_003_01BDFDCF.A3042F40
Content-Type: text/plain;
charset="iso-8859-1"
I have a problem with Radius Accounting packets reporting the wrong NAS
port. When the Radius server recieves a packet for authentication it will
report the correct NAS port but when it sends the Accounting start/stop
packet it always reports NASPort=1.
This problem only seemed to occur after upgrading TCS 3.3
Config is:
Total Control Chassis w/
NMC v5.5.5
HARC v.4.1.11
Hiper DSP v.1.2.5
Radius = IEA Software's RadiusNT v2.5
Thanks
Robb Bryn
------_=_NextPart_003_01BDFDCF.A3042F40
Content-Type: text/html;
charset="iso-8859-1"
<!DOCTYPE HTML PUBLIC "-//W3C//DTD HTML 3.2//EN">
I have a problem with Radius Accounting packets reporting the wrong NAS
port. When the Radius server recieves a packet for authentication it will
report the correct NAS port but when it sends the Accounting start/stop
packet it always reports NASPort=1.
This problem only seemed to occur after upgrading TCS 3.3
Config is:
Total Control Chassis w/
NMC v5.5.5
HARC v.4.1.11
Hiper DSP v.1.2.5
Radius = IEA Software's RadiusNT v2.5
Thanks
Robb Bryn
------_=_NextPart_000_01BDFDCF.A3042F40--