----------------------------------------
Network Operation Centre
World-Link Internet
Ph: (08) 8231 0999
Fax: (08) 8212 8805
support@world-link.com.au
http://www.world-link.com.au
----------------------------------------
-----Original Message-----
From: Ronnie D. Franklin <ronnie@itexas.net>
To: emerald@iea-software.com <emerald@iea-software.com>
Date: Wednesday, 28 July 1999 3:22
Subject: RE: [Emerald] max limit
>If you want to boot them off after 6 hours, but allow them to log back in
>then just add Session-Timeout with a value of 21600 to Service Defaults
>under RadiusNT with Emerald Admin.
>
>
>
>> -----Original Message-----
>> From: emerald-request@iea-software.com
>> [mailto:emerald-request@iea-software.com]On Behalf Of Don Barron
>> Sent: Tuesday, July 27, 1999 10:21 AM
>> To: emerald@iea-software.com
>> Subject: [Emerald] max limit
>>
>>
>> Hi,
>>
>> If I want a certain account type to not be aloud to exceed 6hours
>> connection
>> time what would I do to kick them if they stay connected for 6 hours ?
>>
>> Thanks
>>
>>
>> ----------------------------------------
>> Don Barron
>> Network Administrator
>> World-Link Internet
>>
>> Ph: (08) 8231 0999
>> Fax: (08) 8212 8805
>>
>> don@world-link.com.au
>> http://www.world-link.com.au
>> ----------------------------------------
>> ----- Original Message -----
>> From: Frank Canode <fcanode@mc2k.com>
>> To: <emerald@iea-software.com>
>> Sent: Wednesday, July 28, 1999 12:19 AM
>> Subject: Re: [Emerald] Problem printing invoice - 2.5.278
>>
>>
>> >
>> >
>> > There appears to be only a few of us with this printing problem 2 that
>> > responded to the list and one that I spoke to on the phone. If it works
>> for
>> > eveyone else, then there must be something different about our
>> setup. The
>> > only difference that I am aware of in mine is that I am running Crystal
>> > Reports 7.0 and my database is named Emerald25, not Emerald.
>> The gentleman
>> > that I spoke to on the phone has the same setup - CR 7.0 and database
>> named
>> > Emerald25.
>> >
>> > Any hints in these differences?
>> >
>> > FrankC
>> >
>> >
>> > >I tried that. Same problem. I am running CR 7.0 which was
>> installed after
>> > >the new Emeral client. Any problem there?
>> > >
>> > >
>> > >>Frank Canode wrote:
>> > >>>
>> > >>> Printing invoices with auto batch checked will only produce a
single
>> > >blank
>> > >>> invoice. It finds and reports the correct number of
>> "unsent" invoices,
>> > >opens
>> > >>> the CR window, goes throught the selection process and reports 0
>> > >invoices.
>> > >>> Unchecking auto batch and printing invoices for a specific
>> date works
>> > >>> correctly.
>> > >>>
>> > >>> I did find one post on this problem in the archives but did
>> not find a
>> > >>> solution. Did I miss something?
>> > >>
>> > >>Do you have a modified invoice.rpt? There was a problem with some of
>> > >>the earlier ones that caused simliar problems to this. Grab the
>> > >>latest one from our FTP site and see if that fixes it.
>> > >>
>> > >>--
>> > >>
>> > >>Dale E. Reed Jr. Emerald and RadiusNT
>> > >>__________________________________________
>> > >>IEA Software, Inc. www.iea-software.com
>> > >>
>> > >>For more information about this list (including removal) go to:
>> > >>http://www.iea-software.com/support/maillists/liststart
>> > >
>> > >
>> > >For more information about this list (including removal) go to:
>> > >http://www.iea-software.com/support/maillists/liststart
>> >
>> >
>> > For more information about this list (including removal) go to:
>> > http://www.iea-software.com/support/maillists/liststart
>>
>>
>> For more information about this list (including removal) go to:
>> http://www.iea-software.com/support/maillists/liststart
>>
>
>
>For more information about this list (including removal) go to:
>http://www.iea-software.com/support/maillists/liststart
For more information about this list (including removal) go to:
http://www.iea-software.com/support/maillists/liststart