RadiusNT: [RadiusNT Digest]

..------ ------ ------ ------ ------ ------ ------ ------ ------ ------.| Message 4 |'------ ------ ------ ------ ------ ------ ------ ------ ------ ------'Subject: RE: 3COM/USR Netserver vendor specific attributesFrom: Robb Bryn <rbryn@cape-fear.net>Date: Thu, 4 Jun 1998 10:21:07 -0400

On Thursday, June 04, 1998 1:19 AM, Peter Mott [SMTP:peter@2day.net.nz] wrote:> I would like to be able to log the connection speed in the calls table for a> 3COM/USR Netserver/8 ISDN.>> I have added the Speed_Of_Connection column to the calls table, but it does> not see to record any data.>> Is there anything I need to do to the NAS to get it to send this information> to radiusNT?>> Does anybody know of the location of any resources specific to the> Netserver, as the 3COM site is a minefield to navigate and I dont seem to be> able to find any relevant information.>> regards>> Peter Mott> Chief Enthusiast> 2Day Internet Limited.

3Com has a fairly active list that has been very helpful in getting things working with their TC chassis. I frequently see posts on Netservers as well. The info to subscibe is:

To subscribe to usr-tc, send an email to "majordomo@xmission.com" with "subscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

___________________________________________________________Robert L. Bryn Cape Fear LiveWebmaster PO Box 4741rbryn@cflive.com Wilmington, NC. 28406http:\\www.cflive.com (910)392-9887

The Ultimate Online Magazine for Wilmington___________________________________________________________

..------ ------ ------ ------ ------ ------ ------ ------ ------ ------.| Message 5 |'------ ------ ------ ------ ------ ------ ------ ------ ------ ------'Subject: RadiusNT License Key not workingFrom: "Beverly Wise" <bev@hyper-drive.com>Date: Thu, 4 Jun 1998 11:02:44 -0400

Dale, I was sent our license key for version 2.2 back in February. Now, Ihad no problem running Radius NT in text mode for the last couple of monthseven though the key did not work. Since we are small, and dial up is notour main service, it has not been a problem, till now. We now have 100users, and face the problem. I have taken out the license key, and put itin again. It says 'Error validating key' but goes on.

I am running RadiusNT version 2.2 in text only mode. I have put the companyname and the key in the radius admin box. Each time, it tells me "ErrorValidating Key"

..------ ------ ------ ------ ------ ------ ------ ------ ------ ------.| Message 6 |'------ ------ ------ ------ ------ ------ ------ ------ ------ ------'Subject: Re: Multilink ISDN Logon ProblemFrom: "Kenneth Jordan" <jordan@eaglei.net>Date: Thu, 4 Jun 1998 10:20:01 -0500

OK, I'm not understanding something then. My customer is wanting 128Kaccess. He has been only using one modem and getting 64K DUN access. He justrecently installed another ISDN modem to enable him to get the use of a fullchannel.

I'm using RadiusNT in text mode and Ascend's MAX 4000. Is RadiusNT the placeto configure to give him 128K or is it in the MAX?

-----Original Message-----From: Dale E. Reed Jr. <daler@iea-software.com>To: radiusnt@iea-software.com <radiusnt@iea-software.com>Date: Thursday, June 04, 1998 3:47 AMSubject: Re: Multilink ISDN Logon Problem

>Kenneth Jordan wrote:>>>> I got a customer you has 2 ISDN modems and wanting to multilink link. Hehas>>If you are talking about two ISDN serial terminal adapters, you can't.>Only one think can be in chare of the MPP protocol. For each mode, thats>the modem itself. When you bring two modems together, NT would need to>be the controller, and it can't. The only way this would work would be>to have two serial connections on the TA, acting like two seperate modems.>I don't know of any that have such a thing. You'd be better off trying>to find a device that could take in two BRIs and a Ethernet.>>> a static IP address. He can get the first modem to dial up but when hetries>> to connect with 2nd modem get the msg disconnected from remote host. I'm>> using text mode and here is his configuration:>>>> name Password = "password">> User-Service = Framed-User,>> Framed-Protocol = PPP,>> Framed-Address = 206.24.74.183,>> Framed-Netmask = 255.255.255.0,>> Framed-Routing = Broadcast-Listen,>> Framed-MTU = 1500,>> Framed-Compression = Van-Jacobson-TCP-IP>>>> What am I missing here?>>-->Dale E. Reed Jr. (daler@iea-software.com)>_________________________________________________________________> IEA Software, Inc. | RadiusNT, Emerald, and NT FAQs> Internet Solutions for Today | http://www.iea-software.com

..------ ------ ------ ------ ------ ------ ------ ------ ------ ------.| Message 7 |'------ ------ ------ ------ ------ ------ ------ ------ ------ ------'Subject: From: Spencer Tabbert <SpencerT@NT-SOLUTIONS.com>Date: Thu, 4 Jun 1998 10:27:51 -0500

..------ ------ ------ ------ ------ ------ ------ ------ ------ ------.| Message 8 |'------ ------ ------ ------ ------ ------ ------ ------ ------ ------'Subject: RE: Multilink ISDN Logon ProblemFrom: eric@valleynetworking.com (Eric Cowperthwaite)Date: Thu, 4 Jun 1998 09:17:05 -0700

In RadiusNT you must give him access to two logons. Otherwisehe will only get 64K. He only needs one ISDN terminal adapter(modem) to do this, not two. He cannot bind two modems together.

-----Original Message-----From: radiusnt-request@iea-software.com[mailto:radiusnt-request@iea-software.com]On Behalf Of Richard SensaleSent: Wednesday, June 03, 1998 8:24 PMTo: radiusnt@iea-software.comSubject: Re: Multilink ISDN Logon Problem

I do not think you can multilink 2 ISDN modems. They alreay do this viaMPPP. I have never heard of anything trying to multilink 2 of them for256K.-----Original Message-----From: Kenneth Jordan <jordan@eaglei.net>To: RadiusNT <radiusnt@iea-software.com>Date: Wednesday, June 03, 1998 11:21 AMSubject: Multilink ISDN Logon Problem

>I got a customer you has 2 ISDN modems and wanting to multilink link. Hehas>a static IP address. He can get the first modem to dial up but when hetries>to connect with 2nd modem get the msg disconnected from remote host. I'm>using text mode and here is his configuration:>>name Password = "password"> User-Service = Framed-User,> Framed-Protocol = PPP,> Framed-Address = 206.24.74.183,> Framed-Netmask = 255.255.255.0,> Framed-Routing = Broadcast-Listen,> Framed-MTU = 1500,> Framed-Compression = Van-Jacobson-TCP-IP>>What am I missing here?>>

..------ ------ ------ ------ ------ ------ ------ ------ ------ ------.| Message 9 |'------ ------ ------ ------ ------ ------ ------ ------ ------ ------'Subject: Re: Multilink ISDN Logon ProblemFrom: "Kenneth Jordan" <jordan@eaglei.net>Date: Thu, 4 Jun 1998 11:32:57 -0500

On the second logon account, do I configure it exactly the way I have theother keeping in mind that he needs a static ip, or can I give it a randomip since the first logon has the static ip?

name Password = "password" User-Service = Framed-User, Framed-Protocol = PPP, Framed-Address = 206.24.74.183, Framed-Netmask = 255.255.255.0, Framed-Routing = Broadcast-Listen, Framed-MTU = 1500, Framed-Compression = Van-Jacobson-TCP-IP

-----Original Message-----From: Eric Cowperthwaite <eric@valleynetworking.com>To: radiusnt@iea-software.com <radiusnt@iea-software.com>Date: Thursday, June 04, 1998 11:21 AMSubject: RE: Multilink ISDN Logon Problem

>In RadiusNT you must give him access to two logons. Otherwise>he will only get 64K. He only needs one ISDN terminal adapter>(modem) to do this, not two. He cannot bind two modems together.>>>Eric Cowperthwaite>System Engineer>Valley Networking, Inc.

..------ ------ ------ ------ ------ ------ ------ ------ ------ ------.| Message 10 |'------ ------ ------ ------ ------ ------ ------ ------ ------ ------'Subject: the "delay" problemFrom: miketsai@mail.tonet.net (Michael Y.C. Ysai)Date: Fri, 5 Jun 1998 00:51:29 +0800

------=_NextPart_000_0075_01BD901C.13316450Content-Type: text/plain; charset="big5"Content-Transfer-Encoding: quoted-printable

Hi Dale,Here is the problem after run the latest 2.5.116 version, we user MS SQL =6.5and test with "radlogin test start" and then "radlogin test stop"

radrecv: Request from host 7f000001 code=3D4, id=3D148, length=3D54 NAS-Identifier =3D 127.0.0.1 NAS-Port =3D 0 User-Name =3D "test" Acct-Session-Id =3D "12794148" Acct-Status-Type =3D Start

SQL Statement: UPDATE CallsOnline Set =Username=3D'test',AcctStatusType=3D1,CallDate=3DGetDate(), FramedAddress=3DNULL WHERE NASIdentifier=3D'127.0.0.1' and =NASPort=3D0AND(DateAdd(Second, 0-delay, GetDate()) >=3D CallDate OR CallDate ISNULL)

ODBC Error:S0022:207:[Microsoft][ODBC SQL Server Driver][SQL Server]Invalid column name ='delay'.

Resp Time: 70 Auth: 0/0 -> 0 Acct: 1/0/0 -> 1radrecv: Request from host 7f000001 code=3D4, id=3D167, length=3D60 NAS-Identifier =3D 127.0.0.1 NAS-Port =3D 0 User-Name =3D "test" Acct-Session-Id =3D "12800167" Acct-Status-Type =3D Stop Acct-Session-Time =3D 180

SQL Statement: INSERT INTO Calls(CallDate,NASIdentifier,NASPort,UserName,AcctSessionId,AcctStatusType,AcctSessionTime) VALUES(GetDate(),'127.0.0.1',0,'test','12800167',2,180)

SQL Statement: UPDATE CallsOnline Set =Username=3D'test',AcctStatusType=3D2,CallDate=3DGetDate(), FramedAddress=3DNULL WHERE NASIdentifier=3D'127.0.0.1' and =NASPort=3D0AND(DateAdd(Second, 0-delay, GetDate()) >=3D CallDate OR CallDate ISNULL)

ODBC Error:S0022:207:[Microsoft][ODBC SQL Server Driver][SQL Server]Invalid column name ='delay'.

SQL Statement: UPDATE SubAccounts Set TimeLeft=3DTimeLeft-180 WhereTimeLeft<>NullAnd TimeLeft<>-9999 And Login=3D'test'

Resp Time: 110 Auth: 0/0 -> 0 Acct: 2/0/0 -> 2******************************************************************any idea ?

------=_NextPart_000_0075_01BD901C.13316450Content-Type: text/html; charset="big5"Content-Transfer-Encoding: quoted-printable

Hi Dale,
Here is the problem after run the =latest=202.5.116 version, we user MS SQL 6.5
and test with "radlogin test =start" and then "radlogin test stop"

RadiusNT =Standard=20Initialized...

radrecv: Request from host 7f000001 code=3D4, =id=3D148,=20length=3D54
    NAS-Identifier =3D =127.0.0.1
   =20NAS-Port =3D 0
    User-Name =3D=20"test"
    Acct-Session-Id =3D=20"12794148"
    Acct-Status-Type =3D =Start

SQL=20Statement: UPDATE CallsOnline Set=20Username=3D'test',AcctStatusType=3D1,
CallDate
=3DGetDate(), =FramedAddress=3DNULL=20WHERE NASIdentifier=3D'127.0.0.1' and =NASPort=3D0
AND
(DateAdd(Second,=200-delay, GetDate()) >=3D CallDate =OR       =20CallDate IS
NULL)

ODBC Error:S0022:207:
[Microsoft][ODBC =SQL Server=20Driver][SQL Server]Invalid column name 'delay'.

Sending =Accounting Ack of=20id 148 to 7f000001 (localhost)

Resp Time: 70    =Auth: 0/0=20-> 0 Acct: 1/0/0 -> 1
radrecv: Request from host 7f000001 =code=3D4,=20id=3D167, length=3D60
    NAS-Identifier =3D=20127.0.0.1
    NAS-Port =3D 0
    =User-Name =3D=20"test"
    Acct-Session-Id =3D=20"12800167"
    Acct-Status-Type =3D=20Stop
    Acct-Session-Time =3D 180

SQL =Statement: INSERT=20INTO=20Calls
(CallDate,NASIdentifier,NASPort,UserName,AcctSes
sionId,AcctS=tatusType,AcctSessionTime)=20VALUES
(GetDate(),'127.0.0.1',0,'test','128
00167',2,180)

SQL=20Statement: UPDATE CallsOnline Set=20Username=3D'test',AcctStatusType=3D2,
CallDate
=3DGetDate(), =FramedAddress=3DNULL=20WHERE NASIdentifier=3D'127.0.0.1' and =NASPort=3D0
AND
(DateAdd(Second,=200-delay, GetDate()) >=3D CallDate =OR       =20CallDate IS
NULL)

ODBC Error:S0022:207:
[Microsoft][ODBC =SQL Server=20Driver][SQL Server]Invalid column name 'delay'.

SQL =Statement: UPDATE=20SubAccounts Set TimeLeft=3DTimeLeft-180 =Where
TimeLeft<>Null
And=20TimeLeft<>-9999 And Login=3D'test'

Sending Accounting Ack =of id 167=20to 7f000001 (localhost)

Resp Time: 110   Auth: 0/0 =->=200 Acct: 2/0/0 ->=202
******************************************************************any=20idea ?