It's running now with zeros for Acct! But below is what a page
looks like: I will reboot the Computone tomorrow AM at let you
know what happens. The Computone PR uses an AUI port with a
Transceiver to coax so I adjusted the software to "force" to the
AUI port rather than let the PR detect it. Secondly, I turned
RIP to "none" for each Port that is assigned to each user at
login. Perhaps these two changes will improve how the PR sees
RadiusNT, but not certain. Does anyone using a PR know if this
is an issue?
---------------BEGIN -X15 SCREEN CAPTURE -------------------
SQL Statement: Select DateDiff(Minute, GetDate(), DateAdd(Day,
(ma.Extension+m
..OverDue+1), maExpireDate)), DateDiff(Minute, GetDate(),
DateAdd(Day, sa.Extens
on+1, saExpireDate)), sa.AccountID, sa.AccountType, sa.Password,
sa.Login, sa.S
ell, ma.Balance, ma.OverLimit From MasterAccounts ma, SubAccounts
sa Where sa.
ogin='brown' AND ma.CustomerID=sa.CustomerID and sa.Active<>0
and ma.Active<>0
Checking for duplicate logins.
SQL Statement: RadCheckOnline 'brown'
brown found on-line 0 time(s).
SQL Statement: RadGetConfigs 525
SQL Statement: RadGetATConfigs 'PPP - 25 Hours'
Sending Ack of id 1 to d171a5c5 (iam)
User-Service = Framed-User
Framed-Protocol = PPP
Resp Time: 40 Auth: 4/0 -> 4 Acct: 0/0/0 -> 0
radrecv: Request from host d171a5c5 code=1, id=1, length=73
User-Name = "ronwright"
Password = "G\324i\026 \260/\010\006\341i:`\033\272\015"
NAS-Identifier = 209.113.165.197
NAS-Port = 42
User-Service = Framed-User
Framed-Protocol = PPP
rad_authenticate_ODBC()
SQL Statement: Select DateDiff(Minute, GetDate(), DateAdd(Day,
(ma.Extension+m
..OverDue+1), maExpireDate)), DateDiff(Minute, GetDate(),
DateAdd(Day, sa.Extens
on+1, saExpireDate)), sa.AccountID, sa.AccountType, sa.Password,
sa.Login, sa.S
ell, ma.Balance, ma.OverLimit From MasterAccounts ma, SubAccounts
sa Where sa.
ogin='ronwright' AND ma.CustomerID=sa.CustomerID and
sa.Active<>0 and ma.Activ
<>0
Checking for duplicate logins.
SQL Statement: RadCheckOnline 'ronwright'
ronwright found on-line 0 time(s).
SQL Statement: RadGetConfigs 769
SQL Statement: RadGetATConfigs 'PPP'
Sending Ack of id 1 to d171a5c5 (iam)
User-Service = Framed-User
Framed-Protocol = PPP
Resp Time: 40 Auth: 5/0 -> 5 Acct: 0/0/0 -> 0
------------- END X-15 --------------
Howard A. Brooks, IamNet, Inc. - http://iamnow.net
"Your One Stop Internet Support and Solution Shop" -
howard@iamnow.net
> "Howard A. Brooks" wrote:
> >
> > Hi Dale:
> >
> > I captured the following from the -x15, but was unable to get
> > pick up a log-in, but as I wrote earlier, there was no "bad
> > authenticator" and the Acct: was 0/0/0. I don't know if this
> > will help:
> > RadiusNT 2.5.209 (Emerald Standard) Initialized...
>
> I need an actual request after this though to tell you whats
going on.
>
> --
>
> Dale E. Reed Jr. Emerald and RadiusNT
> __________________________________________
> IEA Software, Inc. www.iea-software.com
>
> For more information about this list (including removal) go to:
> http://www.iea-software.com/support/maillists/liststart
>
For more information about this list (including removal) go to:
http://www.iea-software.com/support/maillists/liststart